Gator Hybrid Seal Low Gloss

Gator Hybrid Seal
Low Gloss

Water based Sealer

No color enhancement

Description

Ideal for

Features

Coverage

Packaging

Description

Ideal for

Features

Coverage

Size	Approximate Surface Sealed
3.78 L (1 U.S. gal.)	100-225 sq. ft (9.3-20.9 sq. m.)
18.9 L (5 U.S. gal.)	500-1125 sq. ft (46.5-104.5 sq. m.)

Coverage will vary depending on joint size and porosity of the surface of the pavers.

Packaging

Product	Retail Size	Per Box	Per Pallet
GATOR HYBRID SEAL LOW GLOSS	1 U.S. gal. (3.78 L)	4 units	24 boxes
GATOR HYBRID SEAL LOW GLOSS	5 U.S. gal. (18.9 L)		48 pails

*The container must be stored at above 0°C / 32°F at all times in order to receive the benefit under the Limited Warranty.

APPLICATION INSTRUCTIONS

PLEASE NOTE

Most paver manufacturers recommend concrete pavers be sealed, 60 days after their installation date.
Do not apply if rain is expected within 24 hours.
Concrete paver surface must be cool to the touch.
Temperature should be between 40°F (5°C) and 85°F (29°C) when sealer is applied.
Wear protective gloves, eye protection and respiratory protection.

STEP 1

ALWAYS REFER to the latest GATOR HYBRID SEAL LOW GLOSS Technical Data Sheet (TDS) at AllianceGator.com before installing GATOR HYBRID SEAL LOW GLOSS.
ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations.

STEP 2

Remove all the stains from the concrete pavers, using Gator Clean products. Use Gator Sealer Stripper to remove any unknown coating that remains on the concrete paver surface.

STEP 3

Remove all contaminated jointing material and replace with Gator Polymeric Sand. Follow the instructions on the back of the bags for proper sand installation.

STEP 4

Wait at least 48 hours at a minimum temperature of 60°F (16°C) and no rain for the Gator Polymeric Sand to properly harden.

STEP 5

Clean the entire surface with the Gator Efflorescence Cleaner. This product will remove the efflorescence trapped in the concrete paver pores as well as thoroughly clean the surface for proper sealer adhesion.

STEP 6

Wait at least 48 hours at a minimum temperature of 60°F (16°C) and no rain so the sand & concrete paver surface are dry.

STEP 7

Best Practice: (See online video. 2 people needed.) Apply one (1) coat of GATOR HYBRID SEAL LOW GLOSS using a sprayer in 60 sq. ft. (5.6 sq. m.) sections, then use a water base foam roller (yellow) to remove the excess sealer or puddle left on the paved surface.

STEP 8

GATOR HYBRID SEAL LOW GLOSS is rain safe and could be used, after 24 hours.

Alliance Designer Products shall not be liable for any non-compliant use.

LIMITED WARRANTY

Before applying the product, the user/buyer must determine its suitability for intended use and user/buyer assumes all risks in that regard. It is a condition of the Limited Warranty that before using the product on the intended larger area, the user/buyer must first test the product on a small less observed area of approximately 4 sq. ft. (0.4 sq. m.) to ensure results meet user/buyer’s expectations. In the event that no test is carried out, the Limited Warranty will only apply to 4 sq. ft. (0.4 sq. m.). Alliance Designer Products Inc. cannot guarantee results as it has no control over surface preparation and product application. If this product is proven to be defective, on the condition that it was applied pursuant to the required method of application and surface preparation, the sole obligation Alliance Designer Products Inc. is to refund the purchase price. Proof of purchase is required for any claim. Alliance Designer Products Inc. shall not be liable for any other damages whatsoever, direct or consequential. To the extent permitted by law, Alliance Designer Products Inc. excludes any implied warranty of quality, merchantability or fitness for purpose.

Alliance Designer Products shall not be liable for any non-compliant use.

*The container must at all times be stored at above 32°F (0°C) to receive the benefit under the Limited Warranty.

Back to top